|
|
outer
dimension |
inner
dimension |
length |
height |
inner
dim. (ht) |
impedance
(ohms)
|
a |
b |
|
d |
e |
M20 |
H |
M |
|
p/n |
fig. |
in. |
(mm) |
in. |
(mm) |
in. |
(mm) |
in. |
(mm) |
in. |
(mm) |
10 MHz |
100 MHz |
250 MHz |
SB- |
1064S |
1 |
0.550 |
13.97 |
0.214 |
5.44 |
1.105 |
28.07 |
0.275 |
6.99 |
|
|
87 |
384 |
588 |
|
1172 |
1 |
0.642 |
16.31 |
0.321 |
8.15 |
0.625 |
15.88 |
0.321 |
8.15 |
|
|
36 |
159 |
244 |
|
1175 |
1 |
0.984 |
24.99 |
0.590 |
14.99 |
0.462 |
11.73 |
0.492 |
12.50 |
|
|
20 |
87 |
133 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
1167 |
2 |
0.325 |
8.26 |
0.125 |
3.18 |
0.600 |
15.24 |
0.158 |
4.01 |
|
|
48 |
211 |
323 |
|
1011S |
2 |
0.620 |
15.75 |
0.260 |
6.60 |
1.050 |
26.67 |
0.295 |
7.49 |
|
|
76 |
336 |
515 |
|
1016S |
2 |
1.020 |
25.91 |
0.314 |
7.98 |
1.125 |
28.58 |
0.510 |
12.95 |
|
|
111 |
488 |
748 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
1094S |
3 |
0.750 |
19.05 |
0.400 |
10.16 |
0.300 |
7.62 |
0.220 |
5.59 |
0.045 |
1.14 |
18 |
79 |
122 |
|
1039S |
3 |
1.500 |
38.10 |
1.050 |
26.67 |
1.000 |
25.40 |
0.270 |
6.86 |
0.065 |
1.65 |
36 |
159 |
244 |
|
1017S |
3 |
2.375 |
60.33 |
1.720 |
43.69 |
1.050 |
26.67 |
0.250 |
6.35 |
0.030 |
0.76 |
29 |
127 |
194 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
1002 |
4 |
0.785 |
19.94 |
0.515 |
13.08 |
1.100 |
27.94 |
0.415 |
10.54 |
0.145 |
3.68 |
45 |
197 |
302 |
|
1085 |
4 |
1.080 |
27.43 |
0.835 |
21.21 |
0.270 |
6.86 |
0.300 |
7.62 |
0.050 |
1.27 |
8 |
36 |
55 |
|
1156 |
4 |
1.755 |
44.58 |
1.355 |
34.42 |
1.125 |
28.58 |
0.490 |
12.45 |
0.060 |
1.52 |
36 |
159 |
244 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| notes: |
1) material designation will
be a prefix for NiZn materials (ie.H-1064S)
or a suffix for MnZn materials
(ie. SB-1064S-M20) |
| 2) impedance values are calculated
and are for reference only (actual values vary per application) |
| 3) magnetic (impedance: ohms/single
turn) tolerance +/-20% |
| 4) mechanical tolerances approximately
+/-1.5% (nominal values may vary per material) |
| 5) length adjustable to suit
application requirements (given existing tool limitations) |
| 6) call if required sizes not
found (not all tool sizes are listed), also see Balun/Multi-hole
Cores |
